How To Jailbreak iPad 1 On iOS 4.3.2 Using Redsn0w [Windows / Mac]

News | Wednesday April 20 2011 5:52 AM | Comments (0) Tags: , , , ,

iPhone Dev team released
, which allows iPad 1 users to jailbreak
(untethered).
In this guide, we will take you through the step by step procedure to
on iOS 4.3.2 using Redsn0w.
Here are some important points to note before you proceed.
This guide is meant for iPad 1 users only. This guide is not meant for iPhone and iPod Touch users. Step-by-step guide for iPhone and iPod Touch users will be available shortly.
and at your own risk.
Please do not forget to backup your iPad before you proceed. You can
for instructions on how to backup your iPad.
After the jailbreaking process is complete, do not forget to checkout our article on
.
Please ensure you are running latest version of iTunes i.e. iTunes 10.2 or later.
Redsn0w 0.9.6rc14 doesn’t support 
.
Download Redsn0w 0.9.6rc14 (
” on your desktop.
You need to download iOS 4.3.2 firmware file (
for iPad 1 (iPad1,1_4.3.2_8H7_Restore.ipsw)
Double click the Redsn0w zip file and extract the application to the Redsn0w folder.
Connect your iPad to the computer, which should automatically launch iTunes.
Skip steps 5 and 6, if your iPad has already been upgraded to iOS 4.3.2.
‘ section on the left pane of iTunes, select your iPad device. Now, hold down the Shift button (Option button for Mac users) and click the ‘
‘ button.
Navigate to the Redsn0w folder on the desktop and select the downloaded iOS 4.3.2 firmware file (iPad1,1_4.3.2_8H7_Restore.ipsw). Click on the ‘
‘ button to let iTunes update your iPhone with the required firmware. You will be asked to setup your iPad 1 either from a previous backup or setup as a new iPad, select the backup you want for your device (ideally should be the most recent one). Wait for iTunes to finish.
Navigate back to the Redsn0w folder and launch the Redsn0w application. If you’re a Windows XP user then try running Redsn0w as ‘Administrator’ (right-click on the Redsn0w exe and select ‘Run as an Administrator’) while Windows 7 users should run the exe in Windows XP mode (right-click on the Redsn0w exe and select Properties, then select the Compatibility tab and select Run this program in compatibility mode for Windows XP).
You will be asked to select the corresponding IPSW file. Click on the Browse button and select the iOS 4.3.2 firmware file (iPad1,1_4.3.2_8H7_Restore.ipsw).
Redsn0w will verify the firmware file and inform you if it has successfully identified it. Click on ‘
‘ to proceed.
Redsn0w will now start preparing the jailbreak data.
You will now be prompted to select the jailbreak options you would like. Make sure Cydia is selected and select ‘
‘ to continue.
You will now be prompted to switch OFF your iPad and plug it to the computer. Follow the instructions and click on ‘
You will now need to put your iPad into the DFU mode. Redsn0w will take you through the necessary steps:
Your iPad should reboot now.
.
Redsn0w will now begin uploading the new RAM disk and kernel.
You will now be notified once the jailbreaking process is complete. Click on the ‘
‘ button to exit the application.
Your iPad will reboot once again (which could take approximately 5 minutes). After it has rebooted, your iPad should be successfully jailbroken. You should find
jailbreak app on your iPad’s home screen.
If you’re new to the jailbreaking world and wondering what to do after jailbreaking your iPad, checkout our 
category page to find out the apps you can install on your iPad using the Cydia app.
Hope this helped. Please don’t forget to let us know how it goes in the comments.

No Comments »

No comments yet.

RSS feed. TrackBack URI

Leave a comment

You must be logged in to post a comment.